Klyde O'Scope
Chameleon Enthusiast
There should also be a folded sheet on how to program the timer. If you didn't get one, you can download a PDF from https://www.mistking.com/instructions.html and print one off.
Set up Mistking v5?
- Thread starter cruz.m
- Start date
Klyde O'Scope
Chameleon Enthusiast
For some reason, it appears you may have 2 bulkheads: one plastic (old style) and one metal (new style). I would use the metal one; it should have a metal nut as well.Does it go like this or just one of them? Actually it doesn’t go like that I just found the other price of the screw, how do I take it out? I’m so dumb
Well I broke it, do they sell replacements for this? It still refuses to come out
Yes, you can get replacements from MistKing or any/most of their dealers.
My eyes are bad, and it's been months since I assembled my system. Up to you, but I'd stop screwing around with the parts.
cruz.m
Avid Member
I fixed it but the timer is not working with me, I know how to use it but now it’s going off and it has two P0 settings. How do you reset the timer?
Attachments
Klyde O'Scope
Chameleon Enthusiast
From the ST-24 Seconds Timer Instructions:
If you have a different timer, you'll have to check its instructions
https://www.mistking.com/instructions.html
cruz.m
Avid Member
Yes that’s why I was concerned, it wouldn’t let me change it but I reset it and it’s good now, thanks everyone!
cruz.m
Avid Member
@Klyde O'Scope @Tige21v
So everything’s set up except when I went to add water it started leaking but not from where the hole was made but the bulkhead front where the tube is. Does anyone know why and how to fix it?
So everything’s set up except when I went to add water it started leaking but not from where the hole was made but the bulkhead front where the tube is. Does anyone know why and how to fix it?
cruz.m
Avid Member
Ok! So the problem is this thing I took it outside just in case but it won’t get to the nozzles it’s coming out of this piece. Yes I did take the covers off the nozzles
Attachments
cruz.m
Avid Member
No, this is from the nozzle. I got the two nozzle system, the nozzles are good but I think it is the same piece as the plastic bulk head I’m just not exactly sure. I want to replace that piece, it come apart from the nozzle. (Picture below)
Attachments
cruz.m
Avid Member
I kind of understand, I got how to pull them apart now though
this is the part that is leaking, I pushed it as far as I could. It drips every five secondsDo you think it would work if I just put the filter piece with the tubing connecting to the pump inside a gallon. It works but I’m concerned about light penetrating inside and causing problems. I could just cover it right? Oh and thank you so much for helping me!
Attachments
Last edited:
DeltaYaz
Member
In case it helps, here are some photos of my setup. I have the Ultimate version and so the ZipDrip solenoid valve is installed between the bucket and the pump.
As far as installing the bulkhead - the O-ring goes on the outside. The previous post regarding the stepped bit is right on - I made mine as close to the size of the bulkhead as possible. I had to thread the bulkhead into the bucket and it was quite tight, but created a good seal, in addition to the O-ring.
Bucket to Pump Connections
Filter Installation
One of the Nozzles
[/url]
As far as installing the bulkhead - the O-ring goes on the outside. The previous post regarding the stepped bit is right on - I made mine as close to the size of the bulkhead as possible. I had to thread the bulkhead into the bucket and it was quite tight, but created a good seal, in addition to the O-ring.
Bucket to Pump Connections
Filter Installation
One of the Nozzles
