Help/feedback on a huge enclosure I’m making

[stickenstein]

Small update for the learning curve!

I tried to use a plywood board at a tilt (supported by 2x4 cuts) with some spray insulation foam for the drainage slant and realized I didn’t like how much enclosure space that cost me. I ended up ripping it all out today and decided to lay down some foam panels to level out the structural gaps in the bottom. Ignore the white pvc stump in the bulkhead, it’s getting removed shortly since it’s unnecessary now. I’m thinking of using lightweight leveling compound or mortar to build a thin slope toward the bulkhead drain but worried about the weight that might add on. I’d assume if it’s thin enough it wouldn’t be a problem but I’m no professional so if anyone can weigh in on that idea, I’d appreciate it!

For the vents, I stapled aluminum screen tightly to the inside and used gorilla waterproof sealing tape to cover the edges and frame it before I seal it again after the drainage is set. I used my miter saw to cut frames for the outer vents and will stain them tomorrow.

I can’t tell if I’m gaining or losing weight from this project. Will post more updates soon

 

[MikeyBen]

Small update for the learning curve!

I tried to use a plywood board at a tilt (supported by 2x4 cuts) with some spray insulation foam for the drainage slant and realized I didn’t like how much enclosure space that cost me. I ended up ripping it all out today and decided to lay down some foam panels to level out the structural gaps in the bottom. Ignore the white pvc stump in the bulkhead, it’s getting removed shortly since it’s unnecessary now. I’m thinking of using lightweight leveling compound or mortar to build a thin slope toward the bulkhead drain but worried about the weight that might add on. I’d assume if it’s thin enough it wouldn’t be a problem but I’m no professional so if anyone can weigh in on that idea, I’d appreciate it!

For the vents, I stapled aluminum screen tightly to the inside and used gorilla waterproof sealing tape to cover the edges and frame it before I seal it again after the drainage is set. I used my miter saw to cut frames for the outer vents and will stain them tomorrow.

I can’t tell if I’m gaining or losing weight from this project. Will post more updates soon

Hi, diy chameleon guys have a great tutorial on the chameleon academy youtube channel about building a drainage layer. You can use plastic corrugate board for the bottom and silicone seal the border. Check out rhe video. Really helpful.

 

[stickenstein]

Hi, diy chameleon guys have a great tutorial on the chameleon academy youtube channel about building a drainage layer. You can use plastic corrugate board for the bottom and silicone seal the border. Check out rhe video. Really helpful.

I’ll check it out now! Thank you so much!

 

[stickenstein]

We have been out of state visiting family but I thought I’d make a quick update while I wait for the next round to flex seal to dry.

Due to the 2x4s breaking up the bottom, figuring out the drainage was tough. I ultimately decided to install 2 drain valves instead of just 1. I used foam board to fill the gaps between the 2x4 braces and added an additional “plateau” of foam in the center to help the excess water slope into the 2 drain areas. I used quikrete to fill the gaps and create additional slope where necessary. Now I’m putting a couple layers of flex seal on top of everything leading down to the bulkheads/drains.

It’s a lot of trial and error and it isn’t the prettiest thing out there, but it’s my first try at building anything or doing any of this so I’m stoked! Hoping my little guy will love his new home when it’s done.

 

[stickenstein]

Coated bottom

Casters and drain valves set into bulkheads

 

[stickenstein]

This might be a dumb ask but does anyone know if there’s any evidence to support whether or not chameleons prefer printed image backdrops (open forests, etc to give the illusion of more space) or closed sculpted foam ones? I want this to be the ultimate environment for my panther. Thanks!

 

[Motherlode Chameleon]

Woww!! I have got to say that this enclosure looks like a Calumma parsonii parsonii enclosure not a Furcifer pardalis enclosure.

Great Job. I am looking forward to watching this enclosure build.

Best Regards
Jeremy A. Rich

 

[dominitri]

Making it taller than I am I can't wait to see how this comes along, so awesome your doing this! Kept up the good work